| 21 | Design of internal permanent magnet motor for electric vehicles | محمدجواد ايزدي | MS. | - | | 25 December 2023 |
| 22 | Development of basic model for battery charge estimation status in electric vehicles by hybrid method | محمد اكبري دوگلسر | MS. | Supervisor | | 18 December 2023 |
| 23 | Design, analyze and experimental study of the core geometry of the polymer-based-composite sandwich structures in order to enhance the vibration and mechanical properties | رضا آزادي | Phd | - | | 13 September 2023 |
| 24 | Clearance control of spatial parallel mechanism using neural networks | باقر جمشيدي | MS. | Supervisor | | 11 September 2023 |
| 25 | Design of a lower limb orthosis with the ability to control resistant torque in the knee joint | سهراب نيك نژاد | MS. | - | | 10 September 2023 |
| 26 | Development of Longitudinal Slip Controller for In-Wheel Drive Electric Vehicle Using Hybrid Regenerative-Hydraulic Braking | نسترن غنمي | MS. | Supervisor | | 12 June 2023 |
| 27 | Vision-Based control of mobile robot and obstacle avoidance | محمد شموشكي | MS. | - | | 30 May 2023 |
| 28 | Modeling and control of micro air vehicle (MAV) | محمد رازقندي | MS. | - | | 14 September 2022 |
| 29 | Investigating the Effect of Piezoelectric Energy Harveting on Dynamic Behavior of Flexible Passive Biped Robot | معصومه صفرتوبي | Phd | Supervisor | | 14 September 2022 |
| 30 | A numerical Simulation of solar dryer chamber with Convex absorber | فاطمه عرش تبار | MS. | - | | 14 September 2022 |
| 31 | Design of Robust Control for adjusting propulsive force of turbo aero engines | علي اردبيلي پور | MS. | Supervisor | | 17 March 2022 |
| 32 | experimental study on effect of spiral minichannel on heat transfer of heat sink | مجيد گرزين | Phd | - | سالن اجتماعات دكتر موسوي | 16 February 2022 |
| 33 | Design and Implementation of Controller for a Quadcopter with the Aim of Flying in a Trajectory with Obstacle | هومن كاتبي | MS. | Supervisor | | 12 February 2022 |
| 34 | Hydro assisted tube pressing process as a new severe plastic deformation method To improve the uniformity of the microstructure of the pure copper tube | علي اصغر ذوالفقاري درزي | Phd | - | | 22 October 2021 |
| 35 | Robust control of a robotic arm using Fuzzy type II algorithm | سينا محمدرضائي نوده | Phd | Consultant | | 20 October 2021 |
| 36 | Fabrication of bone scaffolds by additive manufacturing of FDM process and investigation of their mechanical properties | عاطف نجفي | MS. | - | | 16 September 2021 |
| 37 | Model in the Loop Implementation of Tyre Longitudinal Slip Controller according to experimental model of modulator with the Aim of Antilock Braking | زهرا پيك | MS. | Consultant | | 15 September 2021 |
| 38 | Development of ss304 micro tube bending | مجتبي رويين اهلي | Phd | - | | 15 September 2021 |
| 39 | Develop a new process for the severe plastic deformation of pure copper to achive Ultimate fine grain properties | بهزاد اكبرزاده | Phd | - | | 16 March 2021 |
| 40 | Experimental investigation of heat pipe thermal performance by resurfacing the inner tube of the condenser (Hydrophobic) through nanoparticles and using self-rewetting aqueous solutions in working fluid | خشايار حسين زاده | Phd | - | | 14 February 2021 |
