| 41 | Investigation on microstructure and mechanical properties of Al-Zn-(Ni)p composite produced by semi solid casting | سحر خاكي داودي | MS. | Supervisor | ساختمان مركزي،سالن اجتماعات دانشكده مهندسي مواد و صنايع | 13 February 2022 |
| 42 | characterization of tin oxide doped with carbon nanotube coatings and influence of texture on properties | مهدي زارعي | Phd | Supervisor | | 12 February 2022 |
| 43 | Effect of pre-strain and stacking fault energy on the microstructure and mechanical properties of copper during friction stir processing | حورا مظاهري تهراني | MS. | - | | 09 February 2022 |
| 44 | Lot sizing & Scheduling problem in flexible flow shop with Perishable Product | پريسا پورعبداله | MS. | - | | 08 February 2022 |
| 45 | Effect of the initial microstructure and parameters of electrically assisted forming process on the microstructure and mechanical properties of 2024 Aluminum sheet | نفيسه محمدتبار | Phd | - | | 16 September 2021 |
| 46 | The effect of polycaprolactone (PCL) – hardystonite composite coating on surface properties of magnesium alloy | نيلوفر گودرزي | MS. | - | | 15 September 2021 |
| 47 | Investigation of the effect of plasma parameters on the synthesis of nanostructure Cu oxide film produced by reactive sputtering | خديجه فرهاديان عزيزي | MS. | - | دانشكده مهندسي مواد و صنايع | 15 September 2021 |
| 48 | Investigation of the effect of adding nano particles of copper and graphene on the microstructure and mechanical properties of aluminum matrix composite made by the friction stir processing | احمد اردلان نيا | MS. | Supervisor | | 15 September 2021 |
| 49 | Investigation of Properties of Zinc and Magnesium Coated on Stainless Steel by Physical Vapor Phase Deposition Method | بهاره سلطاني | MS. | Supervisor | | 14 September 2021 |
| 50 | Investigation on microstructure and mechanical properties of Al-Zn-(Ti)p composite produced by semi solid casting | سپيده سالاريه | MS. | Supervisor | | 13 September 2021 |
| 51 | Reverse logistics network design for the waste of electrical and electronic equipment (WEEE): A case study of Mazandaran province | هانيه نجم | MS. | - | | 13 September 2021 |
| 52 | Pomegranate sustainable supply chain network design | سيدحسين حسينيان كاشاني | MS. | - | | 14 February 2021 |
| 53 | Effect of strain path during cold rolling on microstructure, texture and mechanical properties of 304 stainless steel alloy | علي اميني نژاد | MS. | - | | 30 January 2021 |
| 54 | Fabrication and evaluation of Zn/ZnO nanolayer coating properties on calcium phosphate bioceramic | سيمين دخت خادم جعفري | MS. | Supervisor | | 20 January 2021 |
| 55 | Effect of the addition of Ti powders on the microstructure and mechanical properties of A356 alloy by semisolid casting | هانيه عظيمي | MS. | Supervisor | | 18 January 2021 |
| 56 | Development of gradient microstructure in 5052 aluminum alloy by press bonding process | حسين حسن پورشيرسوار | MS. | - | | 05 December 2020 |
| 57 | the Effect of Abrasive Conditions on the Tribological Behavior of Dual- Phase Cast Steel | زهرا محسناتبارفيروزجائي | MS. | - | | 13 September 2020 |
| 58 | Investigation of microstructure and mechanical properties of laminated dual phase steel produced by friction stir welding and heat treatment | محمدرضا رودگري | MS. | - | | 04 February 2020 |
| 59 | Evaluation of the effects of silver powder addition on the microstructure and mechanical properties of AA2024 coating made using friction surfacing process | پريسا پيرحياتي بياتاني | MS. | - | | 02 February 2020 |
| 60 | Effect of friction stir processing on deformation behavior of A390 alloy prepared by the semi-solid casting method | كامران باباپورگل افشاني | MS. | Supervisor | | 01 February 2020 |
