| 1 | The usage of multi-layer rubber mandrel in rotary draw bending of aluminum tubes | محمد جاسم موسي الكيم | MS. | - | | 24 October 2026 |
| 2 | Effect of process parameters on single point incremental forming of high-density polyethylene sheet | علي صلاح احمد الفياض | MS. | - | | 21 October 2026 |
| 3 | Investigation of the effect of process parameters on the final hardness of aluminum truncated pyramids formed using single-point incremental forming process | حيدر عبدزيد عبدالزهره اليميال | MS. | - | | 22 September 2026 |
| 4 | Optimizing wire to cable shoe connection with electromagnetic forming method | محمد رمضاني موزيرجي | MS. | Supervisor | | 21 September 2026 |
| 5 | Studying the effect of geometry and process parameters in order to predict the mechanical properties of porous metal FGM parts in the SLM process | مريم غافري | Phd | - | | 20 September 2026 |
| 6 | A numerical and experimental investigation for enhancing solar panel cooling efficiency utilizing swirl generators and air heat sinks | احمد جبار منصور المالكي | Phd | - | | 17 September 2026 |
| 7 | Comparison of mechanical properties of 3D printed parts by FDM and DLP methods | ماجد مهدي احمد احمد | MS. | - | | 08 September 2026 |
| 8 | Numerical Analysis of Sandwich Panels with Bidirectional Strip Core Under Low-Velocity Impact Loading | علي اصغر رضاييان | MS. | - | تمامي تاريخ و محل جلسه با هماهنگي استاد راهنما تعيين گردد. | 08 August 2026 |
| 9 | Investigation of fatigue behavior of St37 sheets with SS316 coating | دينا عامر حسين الجبوري | MS. | Consultant | | 20 June 2026 |
| 10 | Investigating the Effect of Process Parameters on Prediction and Simulation of a Ductile Fracture Model for Ti6Al4V SLM-Produced Part, and Al Fracture Type Detection from Fracture Surface Images | محمدرضا حسن زاده تلوكي | Phd | - | | 11 May 2026 |
| 11 | improvement of mechanical properties and corrosion behavior of Tungsten arc welding clad martensitic stainless steel over A-517 | حسين رستمي | Phd | - | | 04 April 2026 |
| 12 | Gripping optimization in the case of artificial back bone implementing active joint stiffness control | عليرضا آقامحمدي باسمنج | MS. | - | | 19 February 2026 |
| 13 | numerical investigation on helical vertical axis wind turbine with j type blade for utilization in highways | بهراد دهقان | MS. | - | سالن مرحوم دكتر موسوي | 19 February 2026 |
| 14 | Comparison of tube expansion with electromagnetic forming method using coil and foil evaporation | علي نوكنده | MS. | Supervisor | | 17 February 2026 |
| 15 | The study of electricity assisted L-type bending of Al6061 | سيدمحمد حسيني پناه | MS. | Supervisor | | 17 February 2026 |
| 16 | Study on effective parameters of welding of austenitic Ti-4Al-2V using ultrasonic friction stir welding | حامد رجائي نشلي | MS. | - | | 17 February 2026 |
| 17 | Comparative Analysis of Mechanical Behavior and Failure Modes of Sandwich Composite Panels with Novel Core Materials in Bending After Impact Conditions | محمدحسين مقدم نيا | MS. | - | | 16 February 2026 |
| 18 | Photovoltaic Module Cooling Using Phase Change Material Enhanced with Nanoparticles, Sinusoidal Fins, and Porous Structure | قصي مناف عبدالجبار مصطفي | MS. | - | | 14 February 2026 |
| 19 | The effect of the shape and material of wiper die on the control of wrinkling in the rotary draw bending process of aluminum tube | علي جبار ابوشنه ابوشنه | MS. | - | | 08 February 2026 |
| 20 | The effect of bending angle and radius on springback in aluminum tube bending | قحطان هاشم كطافه كطافه | MS. | - | | 08 February 2026 |
