| 1 | Investigation of Underwater Friction Stir Processing on Microstructure, Mechanical Properties, and Wear Resistance of Al-4.4Cu-1.5Mg Alloy Matrix Composite | Morteza Abedi, Hamed Jamshidi Aval, Roohollah Jamaati | JOM | 2026 | Article In Publication |
| 2 | Deformation-driven metallurgy of AZ91-Hydroxyapatite composites: Insights into microstructure and corrosion resistance | Kimia Jamshidi, Roohollah Jamaati, Hamed Jamshidi Aval | MATERIALS CHEMISTRY AND PHYSICS | 2026 | Article In Publication |
| 3 | Effect of thermo-mechanical age hardening on the strength and electrical conductivity of Copper-AA6063 bimetallic wire | Farnusheh Sharifian amiri, Seyed Jamal Hosseinipour, Hamed Jamshidi Aval, Roohollah Jamaati | Heliyon | 2025 | Article In Publication |
| 4 | Influence of asymmetric rolling paths on the microstructure, texture, mechanical behavior, and electrical conductivity of electrolytic tough-pitch copper | Hanieh Solouki, Roohollah Jamaati, Hamed Jamshidi Aval | MATERIALS CHEMISTRY AND PHYSICS | 2025 | Article In Publication |
| 5 | Cu-Fe Composites Processed by Deformation-Driven Metallurgy: Correlating Structural, Mechanical, Electrical, and Tribological Properties | Zahra Sakhaei, Hamed Jamshidi Aval, Roohollah Jamaati | JOM | 2025 | Article In Publication |
| 6 | Impact of pre-deformation and heat input on the microstructure, mechanical properties, and electrical conductivity of friction stir processed Cu-W composites | Masoome Oliaei, Roohollah Jamaati, Hamed Jamshidi Aval | JOURNAL OF ALLOYS AND COMPOUNDS | 2025 | Article In Publication |
| 7 | Plasma spray coating of HA-Ti-MgO composite on Ti6Al4V alloy substrate | Negin Nadian, Salman Nourouzi, Hamed Jamshidi Aval | Results in Physics | 2025 | Article In Publication |
| 8 | Enhanced strength-ductility synergy in AA5052 alloy through nano/ultrafine structure induced by asymmetric reverse rolling (ARR) | Boshra Ehsani amoli, Roohollah Jamaati, Hamed Jamshidi Aval, Ramezanali Farajollahi, Mousa Javidani | Journal of Materials Research and Technology-JMR and T | 2025 | Article In Publication |
| 9 | Underwater Friction Stir Fabrication and Performance Analysis of <scp>AA2024</scp> Composites Reinforced With In Situ <scp>AlB<sub>2</sub></scp> | Mahna Nikzad dinan, Roohollah Jamaati, Hamed Jamshidi Aval | Engineering Reports | 2025 | Article In Publication |
| 10 | Microstructure, mechanical performance, electrical conductivity, and wear resistance of Cu-Fe composites processed via deformation-driven metallurgy | Zahra Sakhaei, Hamed Jamshidi Aval, Roohollah Jamaati | Journal of Materials Research and Technology-JMR and T | 2025 | Article In Publication |
| 11 | Microstructural characteristics and mechanical behavior of in-situ synthesized AA2024- AlB2 composites produced via friction stir processing | Mahna Nikzad dinan, Roohollah Jamaati, Hamed Jamshidi Aval | Journal of Science-Advanced Materials and Devices | 2025 | Article In Publication |
| 12 | Microstructure and strength analysis of dissimilar resistance welds between interstitial free (IF) steel and low carbon steel | Fatemeh Yaghoobi ashrafi, Roohollah Jamaati, Hamed Jamshidi Aval | Journal of Materials Research and Technology-JMR and T | 2025 | Article In Publication |
| 13 | Hot wear resistance of Cu/Ti2SnC composite wire | Amirhossein Jahani, Hamed Jamshidi Aval, Mohammad Rajabi, Roohollah Jamaati, Annabel Braem | INTERNATIONAL JOURNAL OF REFRACTORY METALS and HARD MATERIALS | 2025 | Article In Publication |
| 14 | Optimizing Microstructure and Performance of Friction Stir Processed Cu-W Composites: The Impact of Predeformation and Traverse Speed | Masoome Oliaei, Roohollah Jamaati, Hamed Jamshidi Aval | ADVANCED ENGINEERING MATERIALS | 2025 | Article In Publication |
| 15 | Influence of Al<sub>2</sub>O<sub>3</sub> Content on Microstucture, Mechanical Strength, and Wear Behavior of AA7075 Matrix Composites via Deformation-Driven Metallurgy | Alireza Ramzani Darvishi, Hamed Jamshidi Aval, Roohollah Jamaati | ADVANCED ENGINEERING MATERIALS | 2025 | Article In Publication |
| 16 | Manufacturing of new dual phase steel with a combination of macro-laminated and micro-laminated morphology | Mohammadreza Roodgari, Roohollah Jamaati, Hamed Jamshidi Aval | CANADIAN METALLURGICAL QUARTERLY | 2025 | Article In Publication |
| 17 | Revealing the Morphology, Crystallographic Texture, and Corrosion Resistance of Electrodeposited ZnO Coatings on Pure Titanium Surfaces | Seyed Reza Torabianfard, Roohollah Jamaati, Hamed Jamshidi Aval | JOM | 2025 | Article In Publication |
| 18 | Investigation of the influence of deposition time on morphology, crystallographic texture, and corrosion resistance of ZnO coatings on titanium substrates | Seyed Reza Torabianfard, Roohollah Jamaati, Hamed Jamshidi Aval | SURFACE and COATINGS TECHNOLOGY | 2025 | Article In Publication |
| 19 | Analysis of the structure and characteristics of bioglass-iron oxide composite layers on Ti-6Al-4V alloy via electrophoretic deposition | Zahra Sohani, Hamed Jamshidi Aval, Sayed Mahmood Rabiee | Composites Part C: Open Access | 2025 | Article In Publication |
| 20 | Manufacturing AA2024-AlB2 in-situ composites: How the traverse speed during friction stir processing influences microstructure and mechanical characteristics | Mahna Nikzad dinan, Roohollah Jamaati, Hamed Jamshidi Aval | JOURNAL OF MATERIALS RESEARCH | 2025 | Article In Publication |
